K
L
Digiplex EVO / Esprit /
Spectra SP Series Panel
G
H
I
J
MG-RTX3 Partial View
M
N
O
C
A B
F
D
E
Figure 3: PGM Connection
Figure 2: ConnectionFigure 1: Mounting
Table 3: Programming without an EVO641/EVO641R
Element
Figure 1: Mounting
A Mounting Holes (x 4)
B Back Cover
C
Antennas: The vertical antenna is the default antenna. Connect the horizontal antenna to improve reception
and range.
D PCB Mounting Holes (x 9)
E Mounting clip (x 4)
F Wiring Slot
Figure 2: Connection
G
ERROR (Red): Indicates a problem with the module.
BUS RX (Green): Flashes when receiving information from the panel.
BUS TX (Red): Flashes when transmitting information to the panel.
RF RX(Green): Flashes when receiving wireless information.
RF TX(Yellow): Flashes when transmitting wireless information.
Special Display (Digiplex EVO only):
BUS RX BUS TX Error Condition
OFF OFF ON Combus is shorted / No clock / No data
OFF ON ON Wrong data / Invalid Combus address (Too many modules)
ON OFF ON Future Use
ON ON ON Combus lines reversed
---- ---- Flash Combus power is too low
H Connect to a 306USB and use WinLoad’s In-Field Firmware Upgrade Application to upgrade the firmware.
I Anti-Tamper Switch
J
Esprit Programming: Press to enter programming mode in Esprit mode.
System Reset: Press and hold the Programming button for 5 seconds, the BUS RX LED will flash. Release the
button and press it again while the LED flashes to reset the module to its default values. This is only possible in
the first 30 seconds after the MG-RTX3 is powered up.
K Connect the Esprit 636/646 LED keypad to the “Program” connector.
L Refer to PGM Connection for connection information.
Figure 3: PGM Connection
M Connect to any device such as a garage door, light or siren.
N Connect to an external Power Supply (PS-817 recommended)
O Note that you should use a relay if the current draw will exceed 150mA.
Digiplex
EVO
Remote
Control
[040] to [043]
View how many of the 32 remotes are used.
[040] = remotes 1 to 8; [043] = remotes 25 to 32.
To delete a remote, press the corresponding number until it’s no longer displayed in these
sections.
[201] to [232]
Assigning remote controls to the MG-RTX3.
[201] = remote 01; [232] = remote 32
Enter the desired section and then press and hold a button on the remote control until you hear
a confirmation beep.
[301] to [332]
Assign the remote controls to users by entering a user number (001 to 255) in the appropriate
section (Users 001 to 255, Section [301] = remote 01, section [332] = remote 32.)
[401] to [432]
Program the remote control or delete the remote control button programming.
[401] = remote 01; [432] = remote 32
______/ ______/ ______/ ______/ ______/ ______/ ______/ ______ (default: 15000000)
(see Figure 4)
(see Figure 5)
[0] = Button Disabled [8] = Panic 2† (Non-Medical)
[1] = Regular Arm [9] = Panic 3† (Fire)
[2] = Stay Arm [stay] = Smoke reset
[3] = Instant Arm [force] = Utility Key 1*
[4] = Force Arm [arm] = Utility Key 2*
[5] = Disarm [disarm] = Utility Key 3*
[6] = Stay/Instant Disarm [byp] = Utility Key 4*
[7] = Panic 1† (Police) [mem] = Utility Key 5*
[clear] = Exit without saving [enter] = Save data
(36 paginas)
(68 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales