Magellan MG5000 Manual de instalación descargar pdf (Pagina 36)

32 Reference & Installation Manual

8.5 Tamper Bypass Options

Section [705]: Zone Options

Option [5] OFF = Tampers on bypassed zones will be ignored

Option [5] ON = Will generate a tamper if detected on a bypassed zone (default)

With option [5] off, the Tamper Recognition feature follows the zone bypass definition. This means the control panel will ignore

any tampers detected on a bypassed zone. With option [5] on, Tamper Recognition ignores the bypass definition. This means the

control panel will generate an incident as per Tamper Recognition settings if a tamper or wire fault occurs on a bypassed zone.

8.6 Tamper Supervision on the Bus Module

Section [700]: Supervision Options

Option [7] OFF = Tamper supervision disabled (default)

Option [7] ON = Tamper supervision enabled

When the control panel detects a tamper on a bus module, the control panel can generate an alarm or trouble, unless the Tamper

Supervision is disabled.

8.7 Keypad Panic Options

Section [702]: General Options

Option [1] OFF = Panic 1 Disabled (default)

Option [1] ON = Panic 1 Enabled

Pressing the [1] and [3] keys simultaneously on the keypad for 3 seconds will generate a silent or audible alarm as defined by

option [4].

Option [2] OFF = Panic 2 Disabled (default)

Option [2] ON = Panic 2 Enabled

Pressing the [4] and [6] keys simultaneously on the keypad for 3 seconds will generate a silent or audible alarm as defined by

option [5].

Option [3] OFF = Panic 3 Disabled (default)

Option [3] ON = Panic 3 Enabled

Pressing the [7] and [9] keys simultaneously on the keypad for 3 seconds will generate a silent or audible alarm as defined by

option [6].

Option [4] OFF = Panic 1 is Silent (default)

Option [4] ON = Panic 1 is Audible

Option [5] OFF = Panic 2 is Silent (default)

Option [5] ON = Panic 2 is Audible

Option [6] OFF = Panic 3 is Silent (default)

Option [6] ON = Panic 3 is Audible

Silent alarm

The control panel emits a confirmation beep and transmits the appropriate Panic report code if programmed in section [863]. The

control panel will not enable the keypad buzzers or the control panel’s BELL output (no audible alarm).

Audible alarm

Same as silent alarm, except the keypad buzzers and the BELL output will activate until a user cancels the alarm (disarms) with a

valid user access code or when the Bell Cut-Off Timer elapses (see Bell Cut-Off Timer on page 31).

Whether the system is partitioned or not, the control panel will report all panic alarms to partition 1.

8.8 Panic Lockout Timer

Section [718]

When a panic alarm is activated, the control panel can ignore the disarm signal from a remote control for a specified period. This

prevents an aggressor from disarming the system by remote control during a panic situation. In section [718] enter a 3-digit value

(000 to 255, 000 = disabled) representing the number of seconds that the remote controls will be locked out of the system.

8.9 Stay/Sleep Arm Alarm Delay

Section [720]

The Sleep Arm Alarm Delay is used to prevent false alarms when the premises is Stay/Sleep armed. In section [720] enter a 3-

digit value (000 to 255, 000 = disabled) representing the number of seconds that the panel will delay an alarm allowing you to

disarm the system (default 15 seconds).

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 55 56

Comentarios a estos manuales

Sin comentarios

Magellan MG5000 Manual de instalación Pagina 36

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Magellan MG5000