Magellan MG5000 Manual de instalación descargar pdf (Pagina 40)

36 Reference & Installation Manual

9.11.2 Ademco Express

The Ademco Express is a high-speed reporting format, which will transmit the 2-digit (00 to FF) report codes programmed

into sections [860] to [876].

9.11.3 Ademco Contact ID

Ademco Contact ID is a fast communicator format that uses tone reporting instead of pulse reporting. This communicator

format also uses a pre-defined list of industry standard messages and report codes that will suit most of your basic

installation needs. Please refer to the Contact ID Report Codes List in the Programming Guide for a complete list of these

report codes and messages. If the reporting codes are set at 0xFF, the MG5000 will send the appropriate report code

from the Automatic Report Code List in the MG5000 Programming Guide. Alternatively, report codes can be

programmed using the Ademco Contact ID Report Codes in the MG5000 Programming Guide.

9.11.4 Event Call Direction

Section [802]: Options [1] to [3]; Arming/Disarming

Option [1] ON =Call MSTN 1

Option [2] ON =Call MSTN 2

Option [3] ON =Call Pager telephone number

Section [802]: Options [5] to [7]; Alarm/Alarm Restore

Option [5] ON =Call MSTN 1

Option [6] ON =Call MSTN 2

Option [7] ON =Call Pager telephone number

Section [803]: Options [1] to [3]; Tamper/Tamper Restore

Option [1] ON =Call MSTN 1

Option [2] ON =Call MSTN 2

Option [3] ON =Call Pager telephone number

Section [803]: Options [5] to [7]; Trouble/Trouble Restore

Option [5] ON =Call MSTN 1

Option [6] ON =Call MSTN 2

Option [7] ON =Call Pager telephone number

Section [804]: Options [1] to [3]; Special Reporting

Option [1] ON =Call MSTN 1

Option [2] ON =Call MSTN 2

Option [3] ON =Call Pager telephone number

Section [804]: Options [5] to [7]; Special Reporting

Option [1] ON =Call voice on zone alarm (burglary/fire)

Option [2] ON =Call voice on panic alarms

Option [3] ON =Call voice on paramedic alarm

The events are divided into six groups (see above) where each event group can be programmed to dial up to three

telephone numbers (MSTN 1 & 2 and the Pager telephone number).

When a reportable event occurs in the system, the Magellan console will begin dialing the numbers sequentially

starting from MSTN 1 (if enabled), skipping any disabled numbers and stopping once all selected telephone numbers

have been called. After a certain amount of failed attempts (section [837]) at trying to call the monitoring station, the

console will then dial the selected backup telephone number (if enabled; see Programming Guide).

If the Alternate Dial option is enabled, the console will dial the programmed backup telephone number (if enabled) after

every failed attempt. If no backup telephone number is programmed, the console will never report to the backup

telephone number.

Example: The system is armed and zone 1 has been breached causing an alarm. If options [5] and [7] are OFF and

option [6] is ON in section [802], the console will attempt to communicate with MSTN 2.

9.11.5 Account Numbers

Section [811]: Partition 1, Section [812]: Partition 2

All report codes are preceded by a 4-digit or 3-digit Partition Account Number to ensure correct identification in a

partitioned system. Partition account numbers can be any hexa-digit from 1 to F. To enter a 3-digit account number,

simply press the [

FORCE] key followed by a 3-digit account number. Also, when using 3-digit account numbers, you

must use 1-digit report codes.

9.12 Dialing Method

Section [800]: Dialer Options

Option [6] OFF = Pulse Dialing (see Pulse Ratio on page 37).

Option [6] ON = Tone/DTMF Dialing (default)

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 55 56

Comentarios a estos manuales

Sin comentarios

Magellan MG5000 Manual de instalación Pagina 40

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Magellan MG5000